Schneider Electric / Square D ABL8RPM24200 Phaseo® Regulated Switch Mode Power Supply; 100 - 240 Volt AC Input, 24 Volt DC, 12 Volt Output, 480 Watt, 20 Amp, DIN Rail Mounting, 1 Or 2 Phase

Detailed Description: Schneider Electric / Square D Phaseo® Electric Commercialized phase regulated switch mode power supply has an input voltage of phase to phase 200 - 240 VAC and 1-Phase 100 - 120 VAC. It features 24 VDC output voltage, 480 Watts rated power and 20 Amps power supply output current. It provides protection against short-circuits, overload, under voltage and overvoltage. It has 47 - 63 Hz network frequency, power factor of 0.69 at 120 Volts and 0.68 at 240 Volts and allows for adjustable 24 - 28.8 Volts output voltage. Dielectric strength is 500 Volts between output and ground, 3000 Volts between input and output and 2500 Volts between input and ground.

Power supply dissipates 57.6 Watts power and has a holding time of 40 milli-seconds at 240 Volts, 20 milli-seconds at 100 Volts and 120 milli-seconds at 400 Volts. It has less than 200 milli-Volts residual ripple and 1 - 3% line/load regulation. It measures 5.708 Inch x 5.511 Inch x 5.629 Inch. It features 35 x 15 mm/35 x 7.5 mm symmetrical DIN rail mount, vertical operating position and series/parallel output coupling. It comes with a green/red/orange LED for output current and a green/red LED for output voltage. Supply requires -40 to 70 deg C ambient air temperature for storage. Relative humidity of 0 - 95% is required during storage and 0 - 90% during operation. It comes with a PFC filter conforming to IEC 61000-3-2 standards.

Power supply features 22 - 8 AWG screw type terminals for output connection with a capacity of 4 x 0.5 sq.mm - 4 x 4 sq.mm, 22 - 12 AWG screw type terminals for input ground connection with a capacity of 1 x 0.5 sq.mm- 1 x 4 sq.mm, 22 - 12 AWG screw type terminals for input connection with a capacity of 3 x 0.5 sq.mm- 3 x 4 sq.mm and removable screw terminal block for diagnostic relay with a connection capacity of 2 x 2.5 sq.mm.

Power supply conforms to EN/IEC 61000-4-5 surge test, IEC 61000-4-4 rapid transient test, EN 55022 Class B Radiated emissions test, EN/IEC 61000-4-3 radiated electromagnetic field test, IEC 61000-4-11 Primary outage test, EN 61000-4-8 magnetic field test, EN/IEC 61000-4-6 induced electromagnetic field test, EN/IEC61000-3-2 Harmonic current emission test, EN/IEC 61000-4-2 electrostatic discharges test and EN 55022 Class B conducted emissions test on the power line. IP20 conforms to EN/IEC 60529 and IP10 for output terminal conforms to EN/IEC 60529 standards. Power supply has safety conforming to SELV, EN/IEC 61204-3, EN/IEC 60950-1 standards and EMC conforming to EN/IEC 61204-3, EN/IEC 61000-6-4, EN/IEC 61000-6-2, EN 61000-6-3 and EN 61000-6-1 standards. It has class I protection conforming to VDE 0106-1 against electric shock. Power supply is UL listed and CCSAus/C-Tick certifications.